FGtech Galletto 4 Master V54 - Full Chip 0475 : Engine ECU programmer via OBD or on desk.
GALLETTO is a simple tool that allows you to read and write original or modified files in the vehicle's ECU through its OBD 2 socket in a few minutes. It communicates with a wide range of ECUs, even the latest generation, and allows you to read and write directly to the ECU's microprocessor, flash memory and EEPROM.
With an intuitive interface it really aims to simplify the handling of professionals and amateurs alike.
You will be able to master the entire reprogramming in a few minutes.
When the OBD2 socket cannot be used for reading and writing, the GALLETTO is equipped with cables for a table connection (BDM JTAG).
You first read the files inside the ECU with GALLETTO, then you have your file professionally modified and finally you write them back into the ECU.
Flexfuel BioEthanol programming with KESS v2 :
The KESS V2 allows you to transform your gasoline vehicle equipped with a multipoint injection into a Flex fuel
It can then run on SP95 / SP98 or E85 Super-Ethanol, without any additional box.
The transformation is fast, simple, economical and totally invisible at the technical control or at the garage. You will have your next fill-up at half price!
Power and torque programming :
You are probably interested in programming upgrades like a Stage 1, a Stage 2 or manipulating options such as EGR valve, FAP, SCR, Adblue, Limiters, etc.
Gain in performance, in comfort and lower your consumption for a very low cost
Reprogram your engine ECU but also that of your friends, or start a new activity, there is no limit of use.
Master Version of GALLETTO :
Full recovery mode
Default DTC analysis and error removal tool
Monitor battery voltage in real time
Etc...
Main advantage of the GALLETTO :
- GALLETTO is able to write via OBD and Tricore BDM
- GALLETTO is ultra compact
- Its software is launched without having to connect to a vehicle
Compatibility of the GALLETTO :
- With many cars, light trucks, trucks, tractors, boats, etc...
- Communication protocols with ECUs until 2012.
GALLETTO Protocols :
NEW JTAG - BDM - MOTOROLA - FREESCALE – INFINEON
Freescale MPC 5553 / 5554 / 5565 / 5566 NEXSUS PORT New IAW MJD 8F2
Delphi DCM3.5xx DCM3.7xx TRW
Motorola Freescale MPC 555 / 556 / 561 / 562 / 563 / 564 / 565
Motorola MC 68332 - MC YQQCU - MC 68377 Trionic 5 / 7 / 8 GM-OPEL-SAAB
Motorola MC 68376 - 01 Lamborghini - Lotus
Motorola MC 68336 MEMS D5 ROVER
Motorola ZC 439615 - ZC 439507 IAW FIAT - VAG
VPM GM - Hummer-Corvette-Munstang-Blazer-Cadilac
Tx-Rx - Subaru - Mitsubishi - Hitachi - Denso ECU
All EDC17 MED17 in Boot Mode.
Automatic Checksum Calculation :
All older protocols are included: Bosch MExx / EDCxx / Marelli / Siemens / Delphi / Lucas / Denso
Boot Mode C167x / ST10
Boot Mode Infineon with Bosch / Siemens password
Motorola MC68332 - MCYQQCU - MC68377 - MC68376 - MC6833 - ZC439615 - ZC439507
Motorola Freescale MPC 555 / 556 / 561 / 562 / 563 / 564 / 565
Freescale MPC 5553 / 5554 / 5565 / 5566
BDM
Industrial vehicless :
K-line, KWP, CAN
Can Bus V2.0 50Kb > 1000Kb
J1850 VPW PWM GM - FORD
Rx Tx RS232
RS 485
K-line 250, 500, 1000 ohm,
Automatique Can Bus 0, 60,120 ohms
Consult the manual, the compatibility list of vehicles, motorcycles, trucks, buses... as well as the different protocols supported by the GALLETTO in the "attached documents" section.
Contents of the GALLETTO package :
1x FGTech GALLETTO 4 interface
1x Cable for boot ECU
1x Adapter for BDM
3x BDM adapters
6x BDM connectors
1x OBD2 cable
1x USB cable
1x EOBD2 software CD
GALLETTO works only on Windows XP and Windows 7 in 32 bits
/ !\ It is important to note that we are not responsible for any misuse of the tools, software or files.
We assume no responsibility for any damage caused to your ECU if incorrect files are used or if a mistake is made!
